New

Lawn & Garden

Wind Chimes

  like (1) I made it (0) Email Print
VIEW ALL Lawn & Garden

STEPS

5

SKILL LEVEL intermediate

Beginner Intermediate Advanced
Upcycle items around the house to make a whimsical wind chime.

by Dremel ®

199 PROJECTS

Tags

home decor

Grid View List View

Supplies Needed For This Project

TOOL

US40 Ultra-Saw™

Model # US40

ACCESSORY

Dremel Ultra-Saw US510 3.5" Metal Cut-Off Wheel

Model # US510-01

ACCESSORY

Dremel EZ456 EZ Lock Cut-off Wheel

Model # EZ456

ACCESSORY

628-01 Drill Bit Set

Model # 628-01

Tools & Accessories

Materials

  • 1

    Drill

  • 1

    1/2" Drill Bit

  • 1

    Hammer

  • 1

    Nail

  • 1

    Pencil

  • 1

    Measuring Tape

  • 1

    9" Aluminum Pie Pan

  • 1

    Soft Metal Spoons

  • 1

    1/2" Copper Pipe

  • 1

    1/2" Copper Caps

  • 1

    Rope

  • 1

    String

  • 1

    Waterproof Epoxy

Let's Get Started

To reduce the risk of injury user must read instruction manuals for all tools used in this project. Wear eye and respiratory protection. Use clamps to support work piece whenever practical.

STEP 1

Step 1

Begin this project by drilling holes in an aluminum pie pan to create the primary support structure for your wind chime. Mark points on the pie pan where you would like each individual chime to eventually hang from. We chose to place five evenly spaced points along the outside brim of our pie pan and three on the interior base approximately 1/2" from its perimeter. With your pie pan clamped, drill through the marked points using your Dremel 4200 rotary tool and 150 Drill Bit accessory. We recommend setting the tool speed to 15 when completing this step. Mark a point at the center of the pie pan and plunge through it using a drill and 1/2" drill bit. In Step 5 we will pull a rope through this hole and use it to hang the wind chime upon its completion.

STEP 2

Step 2

Clamp your spoon by the end of its stem so that the majority of its stem and oval tip are exposed. Mount the EZ456 Metal Cutting Wheel accessory onto your 4200 tool. With the tool set at speed setting 30, make a horizontal cut into the front edge of the oval spoon tip to create a mouth for the fish. Then using the same tool and accessory make two cuts into the stem of the spoon to create a tail. Now we will create an eye hole and functional hanging hole for the fish chime. With your spoon clamped, drill a hole for an eye beside the mouth cut made earlier and a hanging hole close to where the tip of the spoon meets its stem. Use the 4200 tool at speed setting 15 with the 1/8'' accessory to accomplish this.

STEP 3

Step 3

Create copper pipe chimes to be hung through the holes drilled through the interior base of the pie pan support. Repeat the directions below for each copper pipe chime you create. We created three copper pipe chimes. Measure and mark a segment of 1/2" copper pipe to 9" in length. Mount the US510 Metal Cutting Wheel accessory onto your Dremel Ultra-Saw™ tool. Wearing gloves and with the pipe clamped, cut along the mark to create the body of the copper chime. Use a hammer and nail to create an indentation on the top center of a 1/2" copper cap. With your copper cap clamped, plunge through the indentation using your 4200 with the 1/8'' accessory at speed 15. Note that creating the indentation guides the drill bit as you plunge through the cap and prevents it from running along the cap's surface. Apply a waterproof epoxy inside of the cap and slide it onto one end of the copper pipe. Let the epoxy dry.

STEP 4

Step 4

Cut the string used to hang each chime to its desired length. We hung our chimes at staggered heights by cutting their supporting strings to the lengths listed below. Once you have cut your string to size, pull it through the hanging hole of the chime. For the fish chimes this was an additional hole made on the tip of the spoon and for the copper chimes it was the hole made in the cap. Knot the end of the string to fasten it to its respective chime. String Lengths • Copper Chimes: 6", 8", 10" • Fish Chimes: 6", 8", 10", 12", 14" • Step 2 Optional Decorative Centerpiece: 16"

STEP 5

Step 5

Finally, we will tie the chimes to the pie pan support and hang the finished piece with rope. Feed the available end of each string through its respective hole placement on the pie pan support. As a reminder we placed the copper chimes on the interior of our pie pan support and fish chimes along the exterior brim. Knot the strings. Pull rope through the 1/2" hole made in the center of the pie pan in Step 1. We used 36" of rope for our wind chime. Knot the rope. If you created the optional centerpiece in Step 2, tie the available end of its string to the end of the knotted rope. Hang the finished wind chime.

VIEW ALL STEPS SHOW LESS STEPS

Suggested Videos

VIEW ALL VIDEOS

Rotary Tools - How-To

Cutting Pegboard

989

Rotary Tool - DIY

Sharpening a Chainsaw

9519

Saw - DIY

Cutting Wainscotting & Baseboard Trim

940

Rotary Tools - DIY

Cutting Toilet Bolts

913

VIEW ALL VIDEOS

Other Projects You Might Like

VIEW ALL PROJECTS
Rain Barrel
home repair
Rain Barrel

1year ago

Update Kitchen Tile
kitchen
Update Kitchen Tile

3years ago

Shoe Moulding
home repair
Shoe Moulding

2years ago

Soapbox Car
lawn & garden
Soapbox Car

4years ago

VIEW ALL PROJECTS
No Promotion available!

SHOW US WHAT YOU MADE

Send us a photo of your Dremel creation so we can share it with the world.

Submit A Project
No Promotion available!

A TOOL THAT CAN DO IT ALL

Experience Dremel's most powerful oscillating tool. Featuring 7.0 amps of power and 2 new, powerful cutting blades, the Dremel Velocity is the only tool you need.

Learn More

Comments(0)

Sign In to post comments on this project.

No comments yet.

No Promotion available!

Dremel Experts

From drilling holes to distressing denim, Dremel’s Customer Service has an answer.

SUPPORT